Uncategorized

The UJA1161 is a 'self-supplied' high-speed CAN transceiver integrating an ISO11898-2/5 compliant HS-CAN transceiver and an internal 5 V CAN supply. The only supply input is a battery connection. The UJA1161 can be operated in a very low-current Standby mode with bus wake-up capability.

The UJA1023 is a stand-alone Local Interconnect Network (LIN) I/O slave that replaces basic components commonly used in electronic control units for input and output handling. The UJA1023 contains a LIN 2.0 controller, an integrated LIN transceiver which is LIN2.0/ SAE J2602 compliant and LIN 1.3 compatible, a 30kΩ termination resistor necessary for LIN-slaves, and eight I/O ports which are configurable via the LIN bus.

32-bit ColdFire V1 microcontroller with 10/100 Ethernet controller, MII, and multi-function external bus interface.

The TJA1054A is the interface between the protocol controller and the physical bus wires in a Controller Area Network (CAN). It is primarily intended for low-speed applications up to 125kBd in passenger cars.

High speed CAN transceiver for automotive applications up to 1 Mbit/s.

The TJA1029 is the interface between the Local Interconnect Network (LIN) master/slave protocol controller and the physical bus in a LIN network. It is primarily intended for in-vehicle subnetworks using baud rates up to 20 kBd and is compliant with LIN2.0, LIN2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO17987-4:2016 (12V).

The TJA1021 is the interface between the Local Interconnect Network (LIN) commander/responder protocol controller and the physical bus in a LIN. It is primarily intended for in-vehicle sub-networks using baud rates from 1 kBd up to 20 kBd (/20 and B variants) and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016 (12 V).

The TJA1021 is the interface between the Local Interconnect Network (LIN) commander/responder protocol controller and the physical bus in a LIN. It is primarily intended for in-vehicle sub-networks using baud rates from 1 kBd up to 20 kBd (/20 and B variants) and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016 (12 V).

The TJA1021 is the interface between the Local Interconnect Network (LIN) commander/responder protocol controller and the physical bus in a LIN. It is primarily intended for in-vehicle sub-networks using baud rates from 1 kBd up to 20 kBd (/20 and B variants) and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016 (12 V).

Evaluation kit based on i.MX 7ULP applications processors for ultra-low-power processing targeting long battery life devices.

The TFA9879 is a high-efficiency filter-free mono class-D audio amplifier with two separate digital inputs for mobile applications.

Mono BTL class-D audio amplifier for portable applications with digital input

Stereo full-bridge audio amplifier 2 x 17 W

The TFA9815 is a 2-channel power comparator for high-efficiency class D audio amplifier systems. It contains two full-bridge Bridge-Tied Load (BTL) power stages, drive logic, protection control logic and full differential input comparators.

NXP GreenChip low power SMPS controller TEA172x with ultra-low standby and cost-effective power supplies up to 11 W

HV start-up flyback controller with integrated MOSFET for 5 W applications, 430 Hz burst frequency

NXP GreenChip low power SMSP controller TEA172x Ultra-low standby, cost-effective power supplies up to 11 W

I2C-bus controlled 4 x 45 W best efficiency amplifier for automotive applications.

The TDF8546 is one of a new generation of complementary quad Bridge-Tied Load (BTL) audio power amplifiers intended for automotive applications.

I2C-bus controlled 4 × 45 W best efficiency amplifier

The TDF8530 is a quad Bridge-Tied Load (BTL) car audio amplifier comprising an NDMOST-NDMOST output stage based on SOI BCDMOS technology.

The TDA8954 is a stereo or mono high-efficiency Class D audio power amplifier in a single IC featuring low power dissipation. It is designed to deliver up to 2 × 210 W into a 4 Ω load in a stereo Single-Ended (SE) application, or 1 × 420 W into an 8 Ω load in a mono Bridge-Tied Load (BTL) application.

The TDA8953 is a stereo or mono high-efficiency Class D audio power amplifier in a single IC featuring low power dissipation. It is designed to deliver up to 2 × 210 W into a 4 Ω load in a stereo Single-Ended (SE) application, or 1 × 420 W into an 8 Ω load in a mono Bridge-Tied Load (BTL) application.

The TDA8579T is a two channel differential amplifier with 0dB gain and low distortion.

The TDA8579T is a two channel differential amplifier with 0dB gain and low distortion, primarily developed for car radio applications where long connections between signal sources and amplifiers are necessary and ground noise must be eliminated.

2x40W/2W stereo BTL car radio power amplifier with diagnostic facility

The TDA8551; TDA8551T is a one channel 1W Bridge-Tied Load (BTL) audio power amplifier capable of delivering 1W output power to an 8Ω load at THD=10% using a 5V power supply.

The TDA8037 is the cost efficient successor of the established integrated contact smart card reader IC TDA8035. It offers a high level of security for the card performing current limitation, short circuit detection, ESD protection as well as supply supervision.

The TDA8037 is the cost efficient successor of the established integrated contact smart card reader IC TDA8035. It offers a high level of security for the card performing current limitation, short circuit detection, ESD protection as well as supply supervision.

The TDA8035 is the cost efficient successor of the established integrated contact smart card reader IC TDA8024. It offers a high level of security for the card by performing current limitation, short-circuit detection, ESD protection as well as supply supervision.

The TDA8035 is the cost efficient successor of the established integrated contact smart card reader IC TDA8024. It offers a high level of security for the card by performing current limitation, short-circuit detection, ESD protection as well as supply supervision.

The TDA8035 is the cost efficient successor of the established integrated contact smart card reader IC TDA8024. It offers a high level of security for the card by performing current limitation, short-circuit detection, ESD protection as well as supply supervision.

The TDA8034HN is a cost-effective analog interface for asynchronous and synchronous smart cards operating at 5 V, 3 V or 1.8V.

The TDA8034HN is a cost-effective analog interface for asynchronous and synchronous smart cards operating at 5 V, 3 V or 1.8V. Using few external components, the TDA8034HN provides all supply, protection and control functions between a smart card and the microcontroller.

Cost-effective analog interface for multiple smart card slots in POS terminals, supporting up to two main cards and four SAMs.

The TDA8026 is a cost-effective, analog interface for addressing multiple smart card slots in a Point Of Sales (POS) terminal. It can address up to two main cards (synchronous or asynchronous smart cards supported) and up to four Security Access Modules (SAMs).

The TDA8026 is a cost-effective, analog interface for addressing multiple smart card slots in a Point Of Sales (POS) terminal. It can address up to two main cards (synchronous or asynchronous smart cards supported) and up to four Security Access Modules (SAMs).

The TDA8023 is a complete cost-efficient, low-power analog interface for synchronous or asynchronous smart cards.

The TDA5051A is a modem IC, specifically dedicated to ASK transmission by means of the home power supply network, at 600 baud or 1200 baud data rate. It operates from a single 5V supply.

The TDA5051A is a modem IC, specifically dedicated to ASK transmission by means of the home power supply network, at 600 baud or 1200 baud data rate. It operates from a single 5V supply.

The TDA5051A is a modem IC, specifically dedicated to ASK transmission by means of the home power supply network, at 600 baud or 1200 baud data rate. It operates from a single 5V supply.

Very low dropout voltage/quiescent current 3.3 V voltage regulator

Monolithic integrated circuit for controlling the elevation of car headlight beams via a dashboard potentiometer.

Light position controller for passenger cars.

Monolithic integrated circuit for controlling the elevation of car headlight beams via a dashboard potentiometer.

Monolithic integrated circuit for controlling the elevation of car headlight beams via a dashboard potentiometer.

Light position controller monolithic IC for passenger cars, adapts head light beam elevation via dashboard potentiometer.

The TDA19977A; TDA19977B is a three input HDMI 1.3a compliant receiver with embedded EDID memory. The built-in auto-adaptive equalizer improves signal quality and allows the use of cable lengths of up to 25m.

The TDA18250 is a silicon tuner IC designed specifically for high definition cable Set-Top Boxes (STB) supporting single streaming. Used in conjunction with a digital channel demodulator, the TDA18250 covers all worldwide digital cable standards.

The TDA18250 is a silicon tuner IC designed specifically for high definition cable Set-Top Boxes (STB) supporting single streaming. Used in conjunction with a digital channel demodulator, the TDA18250 covers all worldwide digital cable standards.