Part number
Place motor-current capture and result availability deliberately relative to ePWM events, then define the remaining control-loop timing evidence.
Connect MAX3232EUE+T to a 3.3 V UART with correct RS-232 polarity, charge-pump capacitors and wiring, while checking the 120 kbps rating and load limits.
Use MAX3072EESA+T on 3.3 V half-duplex RS-485 buses: separate idle-state fail-safe, line termination, biasing and DE/RE control in industrial designs.
Design with OPA1678IDR using a source-noise budget, input common-mode checks and output headroom limits for low-noise audio stages under real loads.
Check ADP5360ACBZ-2-R7 rail defaults, enable logic and shipment mode before MCU boot, with a register checklist for wearable battery-powered designs.
TI's INA381A1IDSGR combines 20 V/V current sensing and a comparator in WSON-8. Set motor trip thresholds while checking shunt loss, hysteresis and delay.
PM-DB2725EX is a through-hole MIL-STD-1553 transformer with 1:2.5 and 1:1.79 ratios. Match winding taps and test conditions to your avionics interface.
ST's STM32H723VGH6 pairs a Cortex-M7 core with 32 KB data cache in TFBGA100. Check DMA memory access and buffer ownership in industrial control designs.
TDK's ICM-42688-P combines a 6-axis IMU, programmable filters and a 2 kB FIFO. Audit gyro settings after firmware updates in robotics and motion designs.
TI's BQ25798RQMR supports 1-4-cell solar charging with VOC-based MPPT. Check battery support, VINDPM and Hi-Z recovery before changing low-light settings.
IMX425LLJ is Sony’s 1.78 MP monochrome global-shutter sensor with 9 µm pixels and 662.1 fps at 8-bit via SLVS-EC for high-speed FA and ITS cameras.
SN65LBC184DR is a 250kbps TI RS-485 transceiver with integrated 400W peak transient suppression. Learn when system surge exposure still needs external TVS.
AD9833BRMZ-REEL7 is a 12.65mW DDS waveform generator with 28-bit tuning and 12.5MHz output. See how clock, filtering and buffering shape clean output.
ICM-42670-P is a TDK 6-axis IMU with 0.55mA low-noise operation, 3.5µA sleep, a 2.25KB FIFO, motion interrupts and I3C for wearable and drone designs.
LTC3337ERC#TRMPBF is a 100nA primary-battery SOH monitor in a 2mm LFCSP, measuring charge, voltage, impedance and temperature for asset trackers and IoT.
LMC6082AIMX/NOPB is a dual SOIC-8 precision CMOS op amp with 10fA typical input bias for photodiode, transducer and medical sensor front ends. Review limits.
TMUX6211PWR is a 36V, four-channel SPST precision switch in 16-pin TSSOP with 1.8V logic and low leakage for DAQ, test and industrial signal-routing designs.
LEA-M8T-0-10 delivers ≤20 ns clear-sky timing accuracy, dual time pulses and survey-in. Design a traceable GNSS clock for substations and power-grid equipment.
IPW65R080CFDA is a 650 V, 80 mΩ max CoolMOS with fast body diode in TO-247. Learn how conduction, switching, reverse recovery and thermal design cut OBC loss.
XMC4800-E196K1024 AA integrates a 144 MHz Cortex-M4 and EtherCAT slave with distributed clocks. Build deterministic multi-axis motor control on one MCU.
SAK-TC375TP-96F300W AA combines three 300 MHz TriCore CPUs, 6 MB flash, ASIL-D capability, CAN FD and Ethernet. Plan safe automotive domain control systems.
FRDM-MCXN947 pairs a 150 MHz dual Cortex-M33 MCU with a 4.8 GOPS eIQ Neutron NPU. Build a TinyML vision pipeline from camera capture to measured inference.
LPC55S69JBD100 combines 150 MHz dual Cortex-M33, 640 KB flash, TrustZone-M, PUF, and PRINCE. Build a signed boot chain with keys, PFR, and recovery tests.
MIMXRT1052DVL6B runs at 600 MHz with 512 KB RAM and external FlexSPI flash. Build a reliable QSPI boot image with FCB, IVT, XIP, recovery, and reset tests.
AD8253ARMZ-R7 switches gains 1, 10, 100, and 1000 with 10 MHz bandwidth and 780 ns settling. Build a fast sensor DAQ around headroom and ADC drive.
10M04SAU324I7G combines instant-on nonvolatile logic, 246 I/Os, one 12-bit ADC and user flash. See how it simplifies robot I/O, startup and fault monitoring.
XC7Z030-2FBG676I gives Z-7030 radar designs 125K logic cells and 400 DSP slices. See how 2D-FFT preprocessing, burst DMA and resource margin preserve headroom.
XC7Z010-1CLG400C combines dual Cortex-A9 PS with 28K-cell PL. Learn how PS/PL partitioning simplifies FOC, PWM, encoder capture and robot motor control.
AD9361BBCZ integrates 2×2 RF, 12-bit converters and <200 kHz–56 MHz bandwidth for SDRs. Separate its 47 MHz TX and 70 MHz RX limits before design-in.
ZED-F9P-05B supports multi-band RTK and moving-base operation, with 0.01 m + 1 ppm accuracy under specified tests. Check drone power, rates and interfaces.
U-blox NEO-M8L-06B: Automotive Dead Reckoning GNSS Design
We help buyers reduce risk, save time, and secure available stock.
Fast quote for global buyers
