Interface Modules

Connector-Terminal Block Conversion Units for General-purpose Devices, XW2R series. Available with various connection methods including Phillips screw, slotted screw, push-in, and e-CON.

Connector-Terminal Block Conversion Unit with three-tiered terminal block for easier wiring, designed for 16 inputs.

USB 2.0 4-port hub with a Single Transaction Translator (STT).

The XR1009 (single) and XR2009 (dual) are ultra-low power, low cost, voltage feedback amplifiers.

The XR1008 (single) and XR2008 (dual) are rail-to-rail output amplifiers that offer superior dynamic performance with 75MHz small signal bandwidth and 50V/μs slew rate.

The XR1008 (single) and XR2008 (dual) are rail-to-rail output amplifiers that offer superior dynamic performance with 75MHz small signal bandwidth and 50V/μs slew rate.

The XR1009 (single) and XR2009 (dual) are ultra-low power, low cost, voltage feedback amplifiers.

The XR1009 (single) and XR2009 (dual) are ultra-low power, low cost, voltage feedback amplifiers.

The XR1008 (single) and XR2008 (dual) are rail-to-rail output amplifiers that offer superior dynamic performance with 75MHz small signal bandwidth and 50V/μs slew rate.

The XR1008 (single) and XR2008 (dual) are rail-to-rail output amplifiers that offer superior dynamic performance with 75MHz small signal bandwidth and 50V/μs slew rate.

The FT121 G-Sensor shield is designed to connect directly to an Arduino Pro development board. The shield allows the micro-controller on the Arduino Pro to access the FT121 USB device controller.

Vinco is a development module based on the FTDI Vinculum II, VNC2 dual USB host/slave IC. Vinco is designed as a prototyping platform for VNC2 based designs and applications.

Vinco is a development module based on the FTDI Vinculum II, VNC2 dual USB host/slave IC. Vinco is designed as a prototyping platform for VNC2 based designs and applications.

This document provides the hardware specifications of Hybrid Manual Insertion Card Reader of V4KU-*** Series with USB interface. This equipment can read the data of Magnetic Card, and read/write the data of IC card.

Hybrid Manual Insertion Card Reader of V4KU-*** Series with USB interface for reading magnetic cards and reading/writing IC cards.

Hybrid Manual Insertion Card Reader of V4KF-*** Series with RS232 interface for reading magnetic cards and reading/writing IC cards.

Hybrid Manual Insertion Card Reader of V4KF-*** Series with RS232 interface for reading magnetic cards and reading/writing IC cards.

Hybrid Manual Insertion Card Reader of V4KF-*** Series with RS232 interface for magnetic card and IC card read/write.

Low cost, compact manual swipe magnetic card reader with TTL interface.

Low cost, ultra-compact manual swipe magnetic card reader with low power C-MOS technology and multiple configurations.

Low Cost, Ultra-Compact, Manual Swipe Magnetic Card Reader with TTL-compatible interface and multiple track configurations.

Low Cost, Ultra-Compact, Manual Swipe Magnetic Card Reader

Low cost, ultra-compact manual swipe magnetic card reader with TTL interface.

Low Cost, Ultra-Compact, Manual Swipe Magnetic Card Reader with TTL-compatible interface and multiple configurations.

Low Cost, Ultra-Compact, Manual Swipe Magnetic Card Reader with low power C-MOS technology and TTL-compatible interface.

Low cost, ultra-compact manual swipe magnetic card reader with TTL interface.

V2DIP2-64 module is designed to allow rapid development of designs using the VNC2-64Q IC. The V2DIP2-64 is supplied as a PCB designed to fit into a 60 pin 0.8” wide, 0.1” pitch DIP socket.

The USB-RS485-PCB is a USB to RS485 level serial UART converter PCB incorporating FTDI’s FT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. The PCB provides a fast, simple way to connect devices with a RS485 interface to USB.

The USB-COM232-PLUS4 provides a simple method of adapting four legacy RS232 serial devices to a modern USB port using the industry standard FTDI FT4232H USB2.0 Hi-Speed serial bridge chip.

The UMFT602A/X is an evaluation/development module with either HSMC or FMC (LPC) connectors for interfacing FTDI's FT602 32bit FIFO bus to USB 3.1 GEN 1 USB video class (UVC) bridge IC with external hardware.

The UMFT602A/X is an evaluation/development module with either HSMC or FMC connectors for interfacing FTDI's FT602 32-bit FIFO bus to USB 3.1 GEN 1 USB video class (UVC) bridge IC.

Evaluation module for bridging FIFO bus to USB 3.0 host using FTDI's FT60x IC, with FMC or HSMC connectors.

The UMFT60xx is an evaluation/development module with either FMC(LPC)/HSMC connectors for interfacing FTDI’s FT60x USB 3.0 Superspeed IC with external hardware. It allows for bridging a FIFO bus to a USB3.0 host and evaluating the functionality of the FT60x.

The UMFT4222EV is a development module which uses FTDI's FT4222H, a Hi-Speed USB2.0 to QuadSPI/I2C Bridge in compact 32-pin QFN package.

UMFT201XA is a USB to I2C DIP module with a 0.3” row pitch. It is a development module for FTDI’s FT201XQ, one of the devices from FTDI’s range of USB interface bridging integrated circuit devices.

FT121 is a USB generic interface controller with integrated SPI slave interface and advanced features for USB connectivity.

UM232H-B is a multiple-interface Hi-Speed USB to UART, 245 FIFO, FT1248, I2C, SPI and GPIO break-out module.

The TTL-232R-PCB is a USB to TTL serial UART converter PCB incorporating FTDI’s FT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. The PCB provides a fast, simple way to connect devices with a TTL level serial interface to USB.

This manual provides information about using the THS4503 fully differential amplifier on evaluation module PCB marked with Edge # 6439396.

Op Amp Evaluation Boards RoHS

THS3115/25 EVM is an evaluation module for current feedback amplifiers, designed for high-speed applications and PCB design examples.

The TDA8024 is a complete and cost-efficient analog interface for asynchronous 3V or 5V smart cards.

The TDA8020HL is a one-chip dual smart card interface. Controlled by the I2C-bus, it guarantees conformity to ISO7816 or EMV2000 with very few external components.

The TDA8020HL is a one-chip dual smart card interface. Controlled by the I2C-bus, it guarantees conformity to ISO7816 or EMV2000 with very few external components.

Dual IC card interface. The TDA8020HL is a one-chip dual smart card interface.

The TDA8020HL is a one-chip dual smart card interface. Controlled by the I2C-bus, it guarantees conformity to ISO7816 or EMV2000 with very few external components.

The universal operational amplifier evaluation module is a printed-circuit board (PCB) that greatly reduces design time, intended for quick evaluation of amplifiers.