RFQ List
Use this Length Conversion Tool to quickly convert between commonly used length units. Select the original unit in the upper field, choose the target unit in the lower field, and enter a value to instantly generate accurate conversion results. Supported units include kilometers (km), miles (mi), nautical miles (nmi), meters (m), yards (yd), feet (ft), inches (in), centimeters (cm), and nanometers (nm), covering both everyday and scientific measurement needs.
1 cm = 0.393701 in
Introduction
How do you convert metric lengths?
Length is defined as the measurement of the size of an object or the distance between two specific points. When describing an object's dimensions, "length" typically refers to its longest side.
We convert units based on the scale of what is being measured:
Length conversion table
Check out this length conversion table to see what the conversion factors are between nine common length units:
| millimeter (mm) | centimeter (cm) | meter (m) | kilometer (km) | inch (in) | foot / feet (ft) | yard (yd) | mile (mi) | nautical mile (nmi) | |
|---|---|---|---|---|---|---|---|---|---|
| 1 millimeter (mm) | 1 | 0.1 | 0.001 | 0.000001 | 0.03937 | 0.003281 | 0.0010936 | 0.0000006214 | 0.00000054 |
| 1 centimeter (cm) | 10 | 1 | 0.01 | 0.00001 | 0.3937 | 0.03281 | 0.010936 | 0.000006214 | 0.0000054 |
| 1 meter (m) | 1000 | 100 | 1 | 0.001 | 39.37 | 3.281 | 1.0936 | 0.0006214 | 0.00054 |
| 1 kilometer (km) | 1000000 | 100000 | 1000 | 1 | 39370 | 3281 | 1093.6 | 0.6214 | 0.54 |
| 1 inch (in) | 25.4 | 2.54 | 0.0254 | 0.0000254 | 1 | 0.08333 | 0.02778 | 0.000015783 | 0.000013715 |
| 1 foot / feet (ft) | 304.8 | 30.48 | 0.3048 | 0.0003048 | 12 | 1 | 0.33333 | 0.0001894 | 0.00016458 |
| 1 yard (yd) | 914.4 | 91.44 | 0.9144 | 0.0009144 | 36 | 3 | 1 | 0.0005682 | 0.0004937 |
| 1 mile (mi) | 1609344 | 160934 | 1609.3 | 1.6093 | 63360 | 5280 | 1760 | 1 | 0.869 |
| 1 nautical mile (nmi) | 1852000 | 185200 | 1852 | 1.852 | 72913 | 6076 | 2025.4 | 1.1508 | 1 |
There are just two simple steps: 1.Find a conversion factor between the given units and the desired units, and write it as an equation. 2.Convert that equation to a fraction with the desired units on top and the given units on the bottom.
one meter 1m (one meter) is approximately equal to one yard. About 39 inches.
Definition: Length is the distance from one end to the other end of an object, while width is the distance from side to side. Length is a type of measurement that shows how tall or long an object is.
Feet are smaller than meters, so there should be more feet than meters. The conversion is 1 ft = 0.3048 meters.
The difference between length and height is very precise, as length denotes how long a shape is and height denotes how tall it is. Length is the horizontal measurement in a plane whereas height is the vertical measurement.
The definition of length is how long something is, or the amount of vertical space or time it takes up. An example of length is two hours for a movie. An example of length is 12 inches.
1 centimeter is equal to 0.3937 inches, or 1 inch is equal to 2.54 centimeters. ... In other words, 1 centimeter is less than half as big as an inch, so you need about two-and-a-half centimeters to make one inch.
It's about two-thirds as tall as a Bowling Pin. It's about two-fifths as long as a Woman's Footstep. It's about one-third as long as a Man's Footstep. It's about three-tenths as tall as Verne Troyer. It's about one-fourth as tall as General Tom Thumb. It's about one-fourth as tall as Kenny Baker.
Metric units use a base numbering system of 10. Thus a centimeter is ten times larger than a millimeter.
2.54 centimeters The value of 1 inch is approximately equal to 2.54 centimeters. To convert inches to the centimeter values, multiply the given inch value by 2.54 cm.
ICAllIn’s Resistor Color Code Calculator is an interactive tool for identifying resistor values based on 4-band, 5-band, and 6-band color codes. Simply select the colors, and the calculator will display the resistance in Ohms (Ω), tolerance, and power rating. Whether you are building a circuit, repairing electronics, or sorting resistors in your lab, this calculator provides an accurate and efficient way to decode resistor values.
ICAllIn’s Ohm’s Law Calculator helps engineers and students quickly calculate resistance, current, voltage, and power in an electrical circuit. Simply enter any two known values, and the calculator will instantly compute the remaining parameters. This fast and easy-to-use online tool illustrates the fundamental relationship between voltage, current, and resistance, making it essential for circuit design, troubleshooting, and electronics learning.
The Op Amp Voltage and Gain Calculator is an easy-to-use tool for analyzing operational amplifier circuits. It calculates the output voltage, inverting gain, and non-inverting gain based on the input parameters. Simply enter the values of V1, V2, Vp, Vn, and the resistor values R1, R2, R3, and R4, and the calculator will instantly provide accurate results. This tool is suitable for both professional engineers and beginners learning op amp circuit design.
