Interface ICs

The XTR112 and XTR114 are monolithic 4-20mA, two-wire current transmitters. They provide complete current excitation for high impedance platinum RTD temperature sensors and bridges, instrumentation amplifier, and current output circuitry on a single integrated circuit.

The UCC5696 is a 27-line LVD only SCSI programmable terminator. The nominal settings on power up are compliant to SPI-2 through SPI-4.

The UCC5696 is a 27-line LVD only SCSI programmable terminator. The nominal settings on power up are compliant to SPI-2 through SPI-4.

The UCC5681 is an LVD-only Small Computer System Interface (SCSI) terminator that integrates the mode change delay function required by the SPI-3 specification.

The UCC5680 is an LVD-only Small Computer System Interface (SCSI) terminator that integrates the mode change delay function required by the SPI-3 specification.

The UCC5680 is an LVD-only Small Computer System Interface (SCSI) terminator that integrates the mode change delay function required by the SPI-3 specification.

The UCC5680 is an LVD-only Small Computer System Interface (SCSI) terminator that integrates the mode change delay function required by the SPI-3 specification.

The UCC5680 is an LVD-only Small Computer System Interface (SCSI) terminator that integrates the mode change delay function required by the SPI-3 specification.

The UCC5642 is an LVD-only small computer system interface (SCSI) terminator that integrates the mode change delay function required by the SPI-3 specification.

The UCC5642 is an LVD-only small computer system interface (SCSI) terminator that integrates the mode change delay function required by the SPI-3 specification.

The UCC5630A Multimode SCSI Terminator provides a smooth transition into the LVD SCSI Parallel Interface (SPI-2, SPI-3, SPI-4). It automatically senses the bus, via DIFFB, and switches the termination to either single ended (SE) or low voltage differential (LVD) SCSI.

The UCC5630A Multimode SCSI Terminator provides a smooth transition into the LVD SCSI Parallel Interface (SPI-2, SPI-3, SPI-4). It automatically senses the bus, via DIFFB, and switches the termination to either single ended (SE) or low voltage differential (LVD) SCSI, dependent on which type of devices are connected to the bus.

Multimode SCSI terminator with auto selection of single-ended (SE) or low-voltage differential (LVD) modes for SPI-2, SPI-3, SPI-4 buses.

The UCC5629 multimode SCSI terminator provides a smooth transition into the low-voltage differential (LVD) SCSI parallel interface (SPI–2, SPI–3, SPI–4). It automatically senses the bus, via DIFFB, and switches the termination to either single-ended (SE) or low-voltage differential (LVD) SCSI, dependent on which type of devices are connected to the bus.

27-line SCSI terminator with split disconnect

27-line SCSI terminator with split reverse disconnect

UCC5620 provides 27 lines of active termination for a SCSI parallel bus.

UCC5619 provides 27 lines of active termination for a SCSI parallel bus. The SCSI standard recommends active termination at both ends of the cable.

UCC5619 provides 27 lines of active termination for a SCSI parallel bus. The SCSI standard recommends active termination at both ends of the cable.

18-line SCSI terminator with active termination for SCSI parallel bus.

The UCC5614 provides 9 lines of active termination for a small computer system’s interface (SCSI) parallel bus. It complies with SCSI, SCSI-2 and SPI-2 Single Ended Standards and operates from 2.7-V to 5.25-V.

The UCC5519 is a multimode small computer system interface (SCSI) terminator that integrates the mode change delay function required by the SPI–3 specification.

The UCC5511 is a twenty-seven line active terminator for low-voltage-differential (LVD) SCSI networks.

Multi-Mode Low Voltage Differential and Single Ended Terminator for automatic termination of SCSI Bus.

The UC5603 provides 9 lines of active termination for a SCSI (Small Computers Systems Interface) parallel bus.

The UC5603 provides 9 lines of active termination for a SCSI (Small Computers Systems Interface) parallel bus.

The UC5601 provides precision resistive pull-up to a 2.9V reference for all 18 lines in a Small Computer Systems Interface (SCSI) bus cable.

The UC5601 provides precision resistive pull-up to a 2.9V reference for all 18 lines in a Small Computer Systems Interface (SCSI) bus cable.

The UC5601 provides precision resistive pull-up to a 2.9V reference for all 18 lines in a Small Computer Systems Interface (SCSI) bus cable. The SCSI-2 standard recommends active termination at both ends of every cable segment utilizing single ended drivers and receivers.

The UC5601 provides precision resistive pull-up to a 2.9V reference for all 18 lines in a Small Computer Systems Interface (SCSI) bus cable. The SCSI-2 standard recommends active termination at both ends of every cable segment utilizing single ended drivers and receivers.

The UC5181C is an octal line receiver designed to meet a wide range of digital communications requirements as outlined in EIA standards EIA232E, EIA422A, EIA423A and CCITT V.10, V.11, V.28, X.26, and X.27.

The UC5181C is an octal line receiver designed to meet a wide range of digital communications requirements as outlined in EIA standards EIA232E, EIA422A, EIA423A and CCITT V.10, V.11, V.28, X.26, and X.27.

The UC5180C is an octal line receiver designed to meet a wide range of digital communications requirements as outlined in EIA standards EIA232E, EIA423A, EIA422A, and CCITT V.10, V.11, V.28, X.26, and X.27.

The TXS02326 is a complete dual-supply standby Smart Identity Module (SIM) card solution for interfacing wireless baseband processors with two individual SIM subscriber cards.

The TXS02326 is a complete dual-supply standby Smart Identity Module (SIM) card solution for interfacing wireless baseband processors with two individual SIM subscriber cards to store data for mobile handset applications.

USB2.0 High Speed (HS) On-the-Go (OTG) Dual Role Controller

The TUSB6010B is a USB 2.0 HS Dual Role USB Controller designed for seamless interface to an external Host processor through the NOR FLASH-like interface.

The TUSB2551 is a single-chip transceiver that complies with the physical-layer specifications of universal serial bus (USB) 2.0.

The TUSB2551 is a single-chip transceiver that complies with the physical-layer specifications of universal serial bus (USB) 2.0. The device supports both full-speed (12-Mbit/s) and low-speed (1.5-Mbit/s) operation.

The TSC2302 is a highly integrated PDA analog interface circuit. It contains a complete 12-bit A/D resistive touch screen converter (ADC) including drivers, touch pressure measurement capability, and 8-bit D/A converter (DAC) output for LCD contrast control.

The TSC2300 is a highly integrated PDA analog interface circuit. It contains a complete 12-bit A/D resistive touchscreen converter including drivers, touch pressure measurement capability, keypad controller and 8-bit D/A converter output for LCD contrast control.

The TSC2300 is a highly integrated PDA analog interface circuit. It contains a complete 12-bit A/D resistive touchscreen converter including drivers, touch pressure measurement capability, keypad controller and 8-bit D/A converter output for LCD contrast control.

The TSC2111 is a low-power highly integrated high performance codec and touch screen controller, which supports stereo audio DAC, mono audio ADC and SAR ADC.

The TSC2046 is a next-generation version to the ADS7846 4-wire touch screen controller which supports a low-voltage I/O interface from 1.5V to 5.25V.

The TSB43DA42/TSB43DB42 are high-performance consumer electronics 1394 link layer and integrated physical layer devices designed for digitally interfacing advanced audio/video consumer electronics applications.

The TSB43DA42/TSB43DB42 are high-performance consumer electronics 1394 link layer and integrated physical layer devices designed for digitally interfacing advanced audio/video consumer electronics applications.

The iceLynx-Micro is a high performance 1394 link-layer device designed as a total solution for digitally interfacing advanced audio/video consumer electronics applications.

The Texas Instruments TSB43AB21A device is an integrated 1394a-2000 OHCI PHY/link-layer controller (LLC) device that is fully compliant with the PCI Local Bus Specification, the PCI Bus Power Management Interface Specification (Revision 1.1), IEEE Std 1394-1995, IEEE Std 1394a-2000, and the 1394 Open Host Controller Interface Specification (Release 1.1).

1394 link layer controller for ATA/ATAPI storage products, acting as a bridge between 1394 bus and storage devices.

The TSB41LV04A provides the digital and analog transceiver functions needed to implement a four-port node in a cable-based IEEE 1394 network.